Fence Companyin Victorville, CA
A Victorville fence over 3 feet needs a permit, or over 18 inches in a front yard, and the City's chart lists $149 for a non-masonry fence up to 500 square feet and $205 for block. No fence may pass 8 feet. Chain link is barred in front yards of single-family lots under half an acre.
Fences in Victorville mostly divide tract lots. ACS 2024 one-year estimates count 77.6 percent of the 43,797 housing units as single-family detached homes and 42.9 percent as built since 2000, so a typical fence job is a rear-yard run, a side gate or a shared line against a neighbor's block wall on a house from the 1980s through the 2000s. The City traces itself to the Town of Victor, a railroad stop of about 1885, and incorporated on September 21, 1962. Its code now requires new subdivisions to build 6-foot decorative masonry perimeter walls, which is why so many yards back onto block.
For a fence, MDG Builders (CSLB #1040337) plays the general contractor's part: we settle the scope, sort out which City review applies and book a licensed fence subcontractor, with a separate masonry subcontractor when the job is block. The fencing page holds our sourced prices, the Victorville overview lists every trade we manage here, and the guides for San Bernardino and Lancaster show how a nearby Inland Empire city and another high desert city treat the same work. The City's Building Division issues permits. The code text below comes from GoCodebook, a third-party mirror, because Municode and the City's code page returned 403 to us, so confirm every section with the City.
What Victorville's permit list, height rules and Joshua tree chapter say about fences
Where fencing permits come from in Victorville: City of Victorville Development Department, Building Division (Permit Center).
- Fence permits: the City says fences over 3 feet in height, or 18 inches in a front yard, and retaining or garden walls over 18 inches in height (or 30 inches with no footing) need permits; the Municipal Code exempts fences up to 3 feet in rear and side yards and 18 inches in front yards. Fees are $149 for a non-masonry fence up to 500 sq ft and $205 for a block or retaining wall up to 500 sq ft, plus technology, seismic and green fees (stand-alone chart).
- Fence height (Sec. 16-3.24.080 and .090, third-party mirror): no fence or wall may exceed 8 feet measured from the lowest finished ground unless stepped or approved by the Planning Commission, and a fence over 4 feet in a front yard that does not interfere with sight distance can be approved through the minor deviation process.
- Fence materials (Sec. 16-3.08.030, third-party mirror): razor wire and barbed wire are prohibited; chain link is prohibited in new multifamily and in the front or street side yards of single-family lots under a half acre; new subdivisions must build 6-foot decorative masonry perimeter walls and street-side walls.
- City standard details for fences and walls (City Standards page): chain link fence detail, 4 to 6 foot column detail, combo wall detail, fence and wall plot plan, garden wall details for footings centered or on the property line (2 to 7 feet tall) and retaining wall details (2 to 5 feet tall) with the footing away from or under the fill, all posted as PDFs.
Does a Victorville fence need a permit, and where does the 3 foot line sit?
A fence over 3 feet high needs a permit, or over 18 inches in a front yard, and so does a retaining or garden wall over 18 inches, or over 30 inches when it has no footing. That is the wording on the City's Do I Need a Permit page. The Municipal Code, read on the mirror as Sec. 16-5.01.070, exempts fences and walls up to 3 feet in rear and side yards and 18 inches in front yards, and retaining walls up to 30 inches in rear and side yards and 18 inches in front yards, measured from the bottom of the footing.
The City's page and the code phrase the wall limit differently, so ask the Building Division which one the plan checker applies to a wall with a footing. Fees come from the stand-alone chart dated January 8, 2026: $149 for a non-masonry fence up to 500 square feet and $205 for a block or retaining wall up to 500 square feet, plus a 4.6 percent technology fee and seismic and green fees. We could not confirm that the 2025 fee schedule was adopted as proposed, so confirm the total at (760) 955-5100.
Permits are filed online through the Citizen Self Service Portal, and the City publishes a first plan review of approximately 2 to 3 weeks. A fence, dumpster or scaffold placed in public right of way needs an encroachment permit from the Engineering Division through the City's online portal.
Ask the fence company to mark each run as exempt or permitted on the written proposal.
How tall can a fence be in Victorville, and is chain link allowed in the front yard?
No fence or wall may exceed 8 feet, measured from the lowest finished ground, unless it is stepped or approved by the Planning Commission (Sec. 16-3.24.080, mirror). A front yard fence over 4 feet that does not interfere with sight distance can be approved through the minor deviation process, which implies a default front yard limit near 4 feet, though we did not find the base number. We found no rear-yard height below the 8 foot cap, and anything over 3 feet still carries a permit.
Materials are restricted too. Razor wire and barbed wire are prohibited, and chain link is prohibited in new multifamily projects and in the front or street side yards of single-family lots under half an acre (Sec. 16-3.08.030). The City posts standard details for chain link, 4 to 6 foot columns, combination walls and garden walls, which a plan checker can match against your drawing.
Send Planning a sketch before any front yard fence goes above the default height.
What do a 12 inch frost depth, a wind speed conflict and termites mean for fence posts?
The Municipal Code's Table R301.2 lists a 12 inch frost line depth and rates termite damage very heavy, and NOAA's normals show about 54 nights a year at or below 32 F. For wind, the City's Building Codes page gives 100 to 115 mph, mostly 110, while the code table says 96 mph. Those are the City's published figures for buildings. We did not read how they apply to a fence, so we print no footing depth; the City's garden wall details, with footings centered or on the property line for walls 2 to 7 feet tall, are where to look.
UC Integrated Pest Management says drywood termites infest decks and fences and advises termite-resistant wood or concrete footers where wood meets soil, though it speaks of southern California in general and not Victorville. Blowing sand, dust and a summer day-to-night swing near 33 F are part of the desert design conditions. A quote should say what the posts are set in, how deep, and what keeps wood off the soil.
Ask which wind speed the post spacing and footing size were figured against.
Does a Joshua tree on my lot change where I can build a fence in Victorville?
On an occupied home, usually not, but the line is worth knowing. Municipal Code 13.33, read on the mirror, makes it a misdemeanor, up to six months in jail or a $500 fine, to cut, damage, destroy, dig up or harvest a Joshua tree without written consent from the parks and recreation director. The chapter does not apply to occupied residential properties or to existing lots in an already graded and improved subdivision.
It does reach new building. A grading plan must show each tree's surveyed trunk center, tag number, diameter, height and health, and new single-family, ADU and commercial submittals list a Joshua tree inspection report. Grading or moving earth also needs a permit with a wind-generated soil erosion proposal. The California Desert Plant Protection Act separately calls for a state tag when five or more trees are removed. A fence on an unimproved lot, or beside a new custom home, should go past Planning before a post hole is dug.
How do I check zoning, specific plans and my property line before building a fence?
Start with the City's GIS Zoning Checker, which the City says sets each parcel's allowed use, maximum height, minimum setbacks and minimum square footage, and then read its warning that GIS data is for general reference and must be verified independently. Master-planned areas such as Brentwood, Foxfire Ranch, Mesa Verde, Talon Ranch, West Creek and Parkview have posted specific plans whose standards apply in addition to the Development Code, and Old Town has its own specific plan chapters. We opened none of those plan PDFs, so we state no fence rule from them.
An HOA is a separate layer, and we did not research any association's rules. The City also offers a free informal pre-submittal application that planning staff review weekly, which suits an unusual fence. The pages we read do not say who marks property lines; a survey or the recorded map is what settles where the line runs, and that comes before any post is set.
Get the HOA's written approval before the contract is signed.
What rules apply to a pool fence or gate around a Victorville pool?
A pool or spa 18 inches deep or deeper needs a permit, and the City's chart lists $595 for an in-ground pool and $372 for a spa or above-grade pool. Anything shallower is exempt under the code mirror's Sec. 16-5.01.070. The City posts a Swimming Pool Fence Requirements sheet dated June 14, 2011 that shows wood, steel, chain link and masonry barrier types with gate latching notes.
That sheet extracted only partly for us, so we state no barrier height, gate or alarm rule. California's Health and Safety Code 115922 calls for two of seven drowning-prevention features when a permit is issued for a new or remodeled pool, and the enclosure must meet section 115923, though we did not read the height in 115923. Ask the inspector for the current barrier rules before replacing a gate or a fence section around an existing pool.
Ask the inspector which barrier sheet applies before the fence is ordered.
How much does fence installation cost in Victorville, and who pays for a shared fence?
No Victorville fence price survey turned up, so the numbers below are Los Angeles figures. Angi's Los Angeles guide, updated August 4, 2026, shows a $3,051 average and $29 a linear foot within a $15 to $60 range, and its 100 foot row runs $2,100 to $2,350. HomeGuide shows $20 to $60 and Thumbtack $23 to $57. We plan on $25 to $55 per linear foot for a 6-foot wood or vinyl privacy fence, $12 to $30 for chain link and $35 to $85 for aluminum or ornamental iron, which puts a 100 foot backyard run at roughly $2,500 to $5,500. We found no reliable price for block walls or horizontal slat designs.
Fencing is CSLB class C-13, which excludes masonry walls, and block walls fall under C-29, so a block wall and a wood fence can mean two subcontractors. Under Civil Code 841, neighbors who share a boundary fence are presumed to share its cost, and 30 days' written notice comes before incurring any. Business and Professions Code 7159.5 caps a down payment at $1,000 or 10 percent of the price, whichever is less. Our license guide and how general contractors use subcontractors cover who is on site.
Fence photos from Victorville and nearby communities
Fence scenes tied to Victorville places such as Old Town, Victor Valley High School, Desert Valley Hospital and the Mojave River narrows, and to nearby communities such as Adelanto, Apple Valley and Spring Valley Lake, from post footings and block walls to gates and pool barriers.
Where these Victorville fence figures come from
Every fence price, with its source and date, is in the table on the fencing page, and the sources disagree enough that the page lists where. Fence jobs often travel with other exterior work, and the Victorville rules for it are on the roofing page, the painting page and the kitchen remodeling page. To compare against a Los Angeles County city with its own fence height rules, read the fence guide for Glendale.
| What it covers | Typical range |
|---|---|
| Wood or vinyl privacy fence, 6 feet | $25 to $55 per linear foot |
| Chain-link | $12 to $30 per linear foot |
| Aluminum or ornamental iron | $35 to $85 per linear foot |
| Typical 100-foot backyard run | $2,500 to $5,500 total |
| Block walls, horizontal slat fences, gates and openers, hillside lots | Set by the written proposal |
Other work we manage in Victorville
Victorville fence questions, answered
Do I need a permit to build a fence in Victorville?
Yes for a fence over 3 feet, or over 18 inches in a front yard. The City's chart lists $149 for a non-masonry fence up to 500 square feet, plus a technology fee of 4.6 percent and seismic and green fees. Lower fences are exempt under the code mirror, though the permit list is not comprehensive, so call (760) 955-5100 for a fence near the line.
How tall can my front fence be in Victorville?
We found no base front yard number, but the code shows a fence over 4 feet in a front yard can be approved through the minor deviation process if it does not interfere with sight distance. Over 18 inches in a front yard already needs a permit. Ask Planning for the default height for your zone before you design.
Can I put up a 7 foot fence in Victorville?
The code caps any fence or wall at 8 feet from the lowest finished ground unless it is stepped or approved by the Planning Commission, so 7 feet is under the cap. It still needs a building permit, because the exemption stops at 3 feet in rear and side yards. Check the zone's own rules on the Zoning Checker.
Is chain link allowed in a Victorville front yard?
Not on single-family lots under half an acre. The code mirror prohibits chain link in front or street side yards of those lots and in new multifamily projects, and it prohibits razor wire and barbed wire everywhere. A larger lot or a rear yard is a different question, so ask the Planning Division before ordering material.
Do you need a permit to build a block wall in Victorville?
Yes when it passes 3 feet in a rear or side yard or 18 inches in a front yard. The chart lists $205 for a block or retaining wall up to 500 square feet. Block walls fall under CSLB class C-29 masonry, not the C-13 fence class, so expect a masonry subcontractor and a plot plan of the wall.
How much does it cost to have 100 feet of fence installed?
For fence installation, Angi's Los Angeles 100 foot row runs $2,100 to $2,350, and our planning range for a 6-foot wood or vinyl privacy fence is about $2,500 to $5,500 at $25 to $55 a linear foot. These are Los Angeles figures, not a Victorville survey, and they exclude the $149 permit fee, old fence removal and gates.
Does your neighbor have to pay for half the fence in California?
Under Civil Code 841 neighbors who benefit from a boundary fence are presumed to share the cost equally, and the presumption can be rebutted. The statute calls for 30 days' written notice before you incur costs. A fence built entirely on your own side or for your use alone is a different case, so keep the notice and a quote.
What happens if I build a fence without a permit in Victorville?
We found no penalty schedule for unpermitted fences in the sources we read. What the code mirror does say is that a permit extension is refused while a Code Enforcement case is open, and that site trash rules can bring a stop work notice. Ask the Building Division what it requires to legalize an existing fence.
What are the pool fence requirements in Victorville?
A pool or spa 18 inches deep or deeper needs a permit, and the City posts a Swimming Pool Fence Requirements sheet dated June 14, 2011. We could read it only partly, so we state no height or gate rule. State law also calls for two of seven drowning-prevention features on a new or remodeled pool. Ask the inspector for current rules.
Ask for a fence estimate in Victorville
Tell us the lot, the length, the material and whether the line borders a neighbor, a street or a pool. Before we call we check the 3 foot permit line, the zone's height rule and any specific plan or HOA.